Tag Archives: wagon

D&M Models announce pallet cement and beet wagon kits

D&M Models have unveiled two new additions to their range; four-wheel curtain-sided pallet cement wagon and beet wagon kits.

The kits, which feature pre-formed cast resin bodies, etched brass detailing parts and whitemetal buffers, are designed to fit on a Dapol Prestwin chassis (supplied). Decals are also included.

D&M Models pallet cement wagon

D&M Models beet wagon

Both kits are available now. For orders and enquiries, email dmmodelmakers[at]gmail.com.

Advertisements

1 Comment

Filed under News and Views

A Pair of CDR ‘Twins’

Paul Titmuss

 

The twins: the van on the left is from Ninelines, that on the right (and next to the loco in the next photograph) is the Alphagraphix/Inscalemodels combination

The "twins:" the van on the left is from Ninelines, that on the right (and next to the loco in the next photograph) is the Alphagraphix/Inscalemodels combination

Maybe surprisingly there are two kits available for the County Donegal Railways 1893 Oldbury vans in 4mm scale. One is the ‘heritage’ plastic kit by Ninelines, introduced around 1989, the other a card kit by Alphagraphix from around 2002. I’d built the Ninelines kit many years ago when I had first started in 00n3. Very straightforward as you would expect and it is a shame that with the demise of Ninelines it may no longer be available. I was fortunate to acquire the card kit for this van as I wanted to use it for the Inscalemodels brass chassis kit designed for this van (and as a replacement for the basic Ninelines chassis).Care is needed in cutting out the parts for the card kit. I find the corners of the framing the most challenging. I followed the instructions provided. In 4mm scale I would not advise any backing of the timber framing with scrap card, everything seems to fit well without. The painting of the card edge can also be tricky. I used Humbrol enamel paint, applied along the edge, from the back, with a fine brush. It would be helpful to have a suggestion of suitable paint colour to use in the instructions as I’m very poor at colour mixing. With a range of greys in front of me I eventually opted for Humbrol Slate Grey, No 31, which seems a near match for this kit. Other kits will vary.

I’d already soldered together the frames, etc provided by Inscalemodels. They needed shortening a little at each end to fit the van body. I backed them with balsa wood so that they could be stuck to the mount board that formed the floor of the van. The masters of brass out there would do a more professional job I’m sure. I finished the chassis using 10.5mm diameter wheels from Alan Gibson. The roof is made from corrugated plastic-card glued to a balsa former and is removable. The vacuum pipes were completed with brass wire, wrapped around with iron wire for the hose, acceptable at a glance. A brass pin soldered to the pipe fits through a hole drilled into the end of the van and, glued from the inside, will hopefully hold the pipe in place without causing damage to the card if it gets knocked.

Shunting at Lispole... now how did two CDR vans get this far?

Shunting at Lispole... now how did two CDR vans get this far?

Close-up of the Alphagraphix kit

Close-up of the Alphagraphix kit

The Alphagraphix card kit takes much longer to produce and I’ll let the reader judge whether it’s been worthwhile! I find building three card kits a year is enough, though there is something addictive about them and they definitely should not be discounted. I’m currently building the CDR bogie wagon by Alphagraphix, and there is that wonderful combination of a card kit with soldering to tax one’s skills!

[Paul also tells me that his  Annascaul, Lispole and T & DR web sites have gone down with the expiry of his freeserve web address. The preamble from Freeserve said this would not happen, but then it became Wanadoo, and then Orange so he assumes that the rules have changed. At some point in the future he hopes to resurrect them, in a superior format.  Ed]

Leave a comment

Filed under Modelling

GNR Butter Van

Alan O’Rourke

 

In the days when everything went by rail, some companies found it worth while building highly specialised vehicles for perishable traffics, which attracted premium rates, even if it meant those vehicles must have spent half their time running empty. One such traffic was dairy produce, and the MGWR, GSWR and GNR all built special “butter vans.” In the era before electrical refrigeration, these vans employed various cooling mechanisms like double roofs and  multiple small vents in the body, presumably to make full use of the draft when in motion. I have not seen detailed plans of the internal layout of these designs, but I am guessing that they may have been “double-layered” with ice between two skins of planking, or may have used some sort of system where the evaporation of water from a porous surface (as in the older type of terra cotta milk or wine cooler), by taking latent heat of vaporisation from its surroundings, could effect considerable cooling.  I seem to recall a school physics experiment which demonstrated this phenomenon rather well. It involved bubbling air through ether in a copper beaker, the beaker sitting in a small pool of water on a wooden block. By the time all the ether had evaporated, the whole apparatus was so cold that the beaker was frozen to the block by a lump of ice! Alphagraphix now make a 7mm and possibly a 4mm kit for this vehicle. I am grateful to the IRRS archives and Mr Brendan Pender for access to the GNR drawing and permission to reproduce it.

GNR butter wagon

GNR butter wagon

Leave a comment

Filed under Prototype, Scale Drawings

Wagon Portrait

CDR Oldbury open in 15mm scale, built by Neil Ramsay

CDR Oldbury open in 15mm scale, built by Neil Ramsay

The wagon uses Slaters 37mm diameter G1 split spoke wheels and couplings, and axelguards from John Campbell.

Leave a comment

Filed under Modelling

Scratch Building a CIE Cement Bubble

Des Sullivan

 

Prior to its gradual demise, the freight section of  Irish Rail produced some very distinctive and unique rolling stock that just begs to be scratch built.   We have also been blessed that MIR has provided several quality kits in the past few years to recreate them.   The cement bubble has been one of these. However, when I decided to build an eleven to twelve  unit rake of them over twelve months ago, the euro-exchange rate at the time proved to be something of a disincentive.  I also wanted to capture some of the finer detailing that the existing kit as seen from the photo on Steve Johnson’s site didn’t seem to cover.  Since having built them, the euro has strengthened significantly and the kit has been superbly revised (what with a very solid new resin casting of the bubble and gangway and ladder brass etchings).  Oh well, c’est la vie.  I was fortunate in having the opportunity to photograph several of them at the old container sidings in Limerick station which revealed the finer detailing and colouring that would add to building a suitable model.

The basis for most 20’ four wheel CIE freight stock is the Dapol C043 cement wagon.  The distinctive springs, spring hangers and brake levers are all well captured on this model.  Also, because it is a plastic kit, there is much more “depth” to the brake mechanism than one would get with a single piece RTR moulding.  The dimensions are a little out, given that the model is a OO/HO hybrid, but this is really of minor importance compared to the abundance of chassis detailing.  Finally, there are several parts in the C043 kit that with minor alteration can be used to provide the extra detailing needed for the rest of the model.

  
Parts Needed
To build one you will need the following:
  • CO43 kit
  • Two Kinder Eggs – not the hinged type (yes, there are more than one) but the one with the two shells.
  • Guitar string (a light gauge “A” string).
  • A paper lollypop stick (c. 3.6mm diameter).
  • Transfer set (details later).
  • 0.35mm styrene sheeting 30mm x 80mm.
  • Scrap of net curtain material or K & S etched mesh 3/64 diamond.
  • Flexible 0.6mm wire.
  • Milliput.
  • Ratio signal ladder pack (#451).
  • Paint (beige, black, grey, white).

Chassis Construction
First, completely pare back and remove the raised rim on the wagon floor plate (part 6) using a sharp knife or blade.

Scribe and then remove the central part between the two holes.  I drill out several 6mm holes to make this easier.

Chamfer the straight sides of the hole at 45° to make for maximum surface and gluing contact between the bubble/egg and the base.

Construct the chassis as detailed in the Dapol instructions, make sure any flash or mould lines are pared and sanded back.  The main focus of these is at the buffer sides.

Remove the moulded chain from the end hooks prior to fitting as it will impede the coupling bars otherwise.

Widen out the wheels on the axles ever so slightly (0.2-0.3mm). Drill two holes on either side of the frames for the levers.

Base Detailing
The hole left after removing the central section of the plate is too long and will leave a gap at either side when the egg is put in place.  You will need to construct a new wagon floor sheet from styrene sheet that the bubble can sit into, see the adjacent diagram for the appropriate dimensions. 

Remember, fit-check-pare and repeat until a precise fit is got prior to gluing.  Then glue down the sheet onto the original chassis top.  It will take a bit of time, but once done properly, constructing another ten or fourteen can be done with assembly-line ease.   I made a stencil from styrene and used it to draw out and cut the other eleven chassis sheet covers once I was happy with the final dimensions.

Identify the plate (part 44).  This has raised diagonal detailing that matches the prototype closely.   Cut to size by removing paler material as shown in the attached diagram and remove the nodge on the top.  Fit at one end of the  wagon floor sheet, opposite of where the ladders will be.

Construct the cement pipes from chopped up parts 55 and 56.  Mark and drill 0.8mm holes in the floor sheet at the other end (opposite to where plate is on)  and fit.  Bend and then glue some 0.6mm wire to the back. Cut a 5mm length of lollypop stick at a 45° angle using a sharp knife, and mount near the pipes as shown.

Making the Bubble
One of the delights of scratch building this model is that the bog standard Kinder Egg is an almost exact scale replica of the bubble in terms of the hemispherical ends.    It does require lengthening and this is done as follows.Take a male section of one egg and carefully cut off the outer 4mm of the rim.  This is easy enough to do as the egg wall has a thin channel or groove here to act as a cutting guide.

Take the other egg and roughen the ends with sandpaper and then shape a small piece of Milliput so as to round the ends.  I recommend dampening the Milliput , applying to the egg end and then shaping it in the palm of your hand.  Leave to dry overnight. 

Fit the second egg ends together as shown and use the cut off piece from the donor egg (!!) to fill out the gap.  If the rim piece is cut carefully, it should be a perfect fit.  Glue the three pieces together.  Note that the plastic used does not take glue very well (even Superglue) so handle carefully.  It may be worth trying a more full-bodied epoxy glue though I haven’t done this to date. Glue the egg to the chassis base.  Glue some lead window strip underneath to add weight and ballast.

Other Detailing

Fit the manhole cover (part 51) as the Bubble cap.

Bend and glue the guitar wire as vacuum pipe.

The gangway can be made from net-curtain mesh (or K&S etched mesh) with a thin rim of styrene sheet .  Use double thickness styrene triangles as gangway supports and glue to the side of the bubble.

The ladder included in the kit is perfect, but there is only one in each kit!  I suggest Ratio signal ladder as an alternative.  It is also a little finer in scale. 

Fit the manhole cover (part 51) as the Bubble cap.


Bend and glue the guitar wire as vacuum pipe.


The gangway can be made from net-curtain mesh (or K&S etched mesh) with a thin rim of styrene sheet .  Use double thickness styrene triangles as gangway supports and glue to the side of the bubble.

The ladder included in the kit is perfect, but there is only one in each kit!  I suggest Ratio signal ladder as an alternative.  It is also a little finer in scale.

Given that a rake of fifteen  will probably remain permanently connected, for added realism I suggest using the coupling provided for the end wagons, and very light gauge wire loop glued to the hooks to connect each of the interim wagons.

Note: I will be producing a brass etch of the gangway and supports as an all-in-one bendable unit as an alternative to the above.  It will also include the ladders.  This should be available in January 2009.*

Painting and Transfers
Painting offers a few challenges as the model has had several liveries, including orange and beige.  However for the last decade and more, most of them are an interesting mottled shade of greyish white with algae green streaks.  The chassis originally was black but is now usually a non-descript grey-brown. If you are going to be building or repainting any volume of models,  I strongly recommend purchasing a good quality air brush, such as an Iwata HP-CS and a mini-compressor.  These can be got for quite good value off eBay.  The simple reason is you can paint a brace of kits in a matter of minutes using diluted acrylic paint with a smooth, uniform coat that covers even the most inaccessible parts, dries quickly and allows repainting almost immediately.

Paint the model in the following order:

  • Paint the entire kit in white primer.
  • Spray-paint the chassis and wheels in a lightish grey brown.
  • Spray the bubble beige (mask as necessary).
  • Fit the “Broken Circle” and cement decals. I made up my own stencil type transfers of the CIE circle, “Cement,” model numbers and wheel inspection dates. Contact me if you are interested in sets of these.*
  • From overhead, use a criss-cross alternating mixture of white and primer grey to get a non-uniform finish approximating to ten years of cement coating. Another option is to spray a thin mist of water and then sprinkle minute amounts of fresh dry Polyfilla powder through a very fine sieve to get the layered cement look.
  • Bend and attach the side levers using 0.6mm wire into the pre-drilled holes, paint white and then yellow.
  • Paint the cement pipes a darker shade of grey/brown.
  • Paint the ends of the brake lever white then red.
  • Paint the sole-bars at appropriate points as indicated in the picture and fit the chassis numbering and inspection stencils.

To Conclude…
Oh the hours of blood, sweat and tears that can be summarised in little over three pages!   However, taking the approach as laid out above and tackling them in an assembly line fashion, you can build a fifteen-unit rake for little over €100 in a matter of days.  The main points to re-iterate are: get plenty of pictures to be in that comfort zone about the detail locations and take your time to get the chassis cut out and chassis sheet dimensions and angles correct.  You’ll be well rewarded.  In a future issue, I’ll tackle how to build the 20’ beet wagon using Corrugated sheeting.  Nice!

[Ed: I once weathered a OO lime wagon with toothpaste, which looked like a thick coat of chalky minerals, but I would advises a test-patch, as some paint finishes may not tolerate tooth-paste.]

 

* dezsullivan@eircom.net

Leave a comment

Filed under Modelling

CIE Four-Wheeled Bulk Cement Wagons

Robert Drysdale

 

The four-wheeled cement wagons, or “bubbles” as they are popularly known, are iconic of the modernisation of Irish Railways in the 1960s.  They are continuously popular subjects for modelling, so in this article a few observations are offered with that use in mind.  One hundred and fifty of these wagons were constructed over a period of eight years and most, I guess, are still in service.  The batch numbers are as follows:

  • 25050 – 25069 (1964)
  • 25070 – 25094 (1965)
  • 25095 – 25099 (1967)
  • 25105 – 25119 (1967)
  • 25120 – 25139 (1970)
  • 25140 – 25199 (1972)

The sub-plot of the article is about what information can be extracted from the Worldwide Web.  With the advent of the web and the digital camera many excellent images have suddenly become publicly available representing an unparalleled information source.  Of course, lacking access to the prototype, a lot of “reverse engineering” is necessary to guess how things are.  A list of websites used is given at the end of this article: if the reader is not yet computer-literate then find an internet café, order a coffee and get started!  I started this work in order to gather information for creating a rake of cement bubbles.  The only drawing I had was the one which came with an MIR kit, which is quite good.  Then I started searching the web for photographs.  What became clear quite quickly was that although these wagons may seem to be standard, there are actually subtle differences which reflect the building batches and modifications carried out in service.  These details might seem a bit too trivial for most people, but I believe that a little variation adds considerably to the realism of a rake of standard wagons.  My notes on this aspect are as below.

Detail Variations
Solebars: it seems as though these wagons have been built with the stronger springs and spring-hangers of the later four-wheeled stock, presumably reflecting their load capacity of 20 or 21 tons.  There are many variations of lifting lugs within the class, which may be two, one or none per side and presumably not necessarily the same number on both sides.  Likewise the mounting plate for these lugs may be rectangular, notched or absent and in the latter case various stiffening ribs can be seen instead.

Buffers: two types can be seen on the photographs, both massive parallel items.  One (older?) type has a smaller base plate which fits inside the open channel section buffer beam.  Note that the buffer beam is arranged with the open channel outwards.  The larger buffer is attached to an additional plate welded across the webs of the open channel.  Whearas the larger buffer has a relatively plain housing, the smaller one is lumpy with a distal bulge on each side of the housing and a flat rectangle on the top surface next to the ram.

Axleguards: most of the axleguards are solid plate items, but some photographs show the earlier fabricated type with a triangular opening on each side of the spring.  This can be seen on other wagons of the same era.

Axleboxes: on a few photographs heavily bolted wing-plates can be seen on the side of the axleboxes, while most wagons have plain wings.  Earlier wagons had a plain dished end-cover whereas most of the photographs on the web show the Timken boxes with the characteristic triangular three-bolt end plate.

Unloading Valves: on most photographs, two small yellow-painted handles emerge from holes in the solebar, which control the outlet valves from the tank.  Although the little holes seem to be provided on both solebars, the handles appear on only one side.  I can see no convention as to which solebar the handles should be on, but there seems to be about equal numbers on left and right-handed examples.

Vacuum Cylinder Covers: the cylinders are located at one end of the wagon and protrude slightly above the chassis, necessitating a chequer-plate platform for safe walking over this area.  In a large number of examples this plate has been removed, exposing the vacuum cylinders and chassis, which poses an interesting challenge for the modeller.

Unloading Pipe: at the opposite end of the wagon from the brake system is the unloading pipework.  The main unloading pipe of 6″ diameter emerges from the decking at about 60° and is provided with a loose cover, which may be either cylindrical or rectangular.

It is debatable how much variation in these details can be seen in one rake of wagons.  New wagons would probably have entered service in very uniform condition but over time modifications would have been made and the various batches would have become mingled.

Colour
According to advice gleaned from the Irish Railway Modellers web group, the bulk cement wagons have had three liveries so far.  Initially they ran in a light-to-mid grey, then were repainted into CIE orange and finally many were given the Irish Cement ivory colour.  Of course since the cement is dumped into the top hatch via a loose hose a lot spills over the tank and ditto for the unloading platform.  Given some rain this cakes nicely and holds track dust providing a glorious spectrum of very off-white to brown colours, interspersed with patches of virgin white where the cake has flaked off.  Many tanks show a haze of light brown over the lower half of the tank suggesting track dirt and/or rust.  A competition for the most realistically painted and weathered cement bubble would be in order!

Operating Practice
We are told we should try to run our model railways realistically, so with that in mind it is worth examining the photographs for operational purposes.  I have read various opinions about how many wagons rakes consist of, namely 12 wagons per rake originally later increasing to 20.  Photographs of an unloading operation at Adelaide show the wagons arranged in pairs, i.e. with the unloading pipes towards each other.  Presumably this is to allow the unloading pipes to be transferred easily from one wagon to the second.  However, most photographs show a more irregular order, presumably after some shunting.  Despite the apparent complexity, the air unloading system allows unloading the wagon into a lorry-mounted tank, which must be equipped with a suitable air blower.  Thus a large unloading installation is unnecessary and cement can be delivered at a simple siding – see the example at Waterside, page 66 in Ulster Transport in Colour by Derek Young.

For completeness I should mention my understanding of how the unloading system works, based on the information available for BR’s Presflow wagons.  “Fluidised bed” is common in industry to make a heavy mass of powder behave like a fluid by pumping high pressure air through it.  The bottom of the cement tank is formed into two cones and it seems most likely that compressed air is injected into each via some sort of distributor ring (I’m guessing here) to fluidise the cement in the bottom of each cone.  When the valve on the bottom of a cone is opened, the cement flows out into the large diameter unloading pipe, which emerges up through the decking of the unloading platform and into the unloading hose of the terminal or truck.  The instructions for the Presflow state that the pipe-work must be purged with air before opening the cement valves in order to clear any water which has collected in the system, which seems wise.  Loading is via the large hatch on top of the tank, most likely by gravity and since this is not a closed system, spilllage occurs.

If any reader is able to shed more light on my observations I would be very glad to receive them on merlin-x@online.no.

 

Reference Websites For Photographs
onirishrailways2.fotopic.net/c948803.html
railsceneireland.fotopic.net/c1365051.html
irishrailciefreightandrollingstockpics.fotopic.net/c1494361.html

[We hope to have scale drawings of these characteristic vehicles in a future issue. Ed]

1 Comment

Filed under Prototype