Tag Archives: LMS (NCC)

Station Surveys

Alan O’Rourke


We seem to have neglected the NCC so far in this occasional series, so maybe time to rectify that!

Magherafelt was unusual in being a double junction. Mention the Northern Counties, and most people will think of the Belfast-Derry mainline and the branches and narrow gauge to the north east, but there was a also a less well known system of secondary routes to the south west, with Magherafelt as its nodal point. In NCC days, it was the location of a permanent way inspector whose remit covered the lines to Draperstown, Macfin, Cookstown and Cookstown Junction. The first section was a short branch from Drumsough Junction (after 1856, Cookstown Junction) to Randalstown, tacked onto the Belfast & Ballymena Railway (BBR) and opened on the same day (12th April, 1848), to provide a connection with the proposed Dublin, Belfast & Coleraine Junction Railway. When this failed to materialise, the BBR extended the line through Staffordstown and Magherafelt to Cookstown in 1856. The GNR also served that town from 1879. Magherafelt became a junction in 1880 with the opening of the Derry Central Railway north to Macfin, although most services ran through to and from Coleraine. The Draperstown Railway added an eight mile branch westward, with one intermediate station at Desertmartin in 1883. Neither of these concerns was financially successful, being absorbed into the Belfast & Northern Counties Railway (as it had then become), in 1901 and 1895 respectively. Obeying the “last in, first out” rule, the Draperstown branch lost its passenger services in 1930. The only passenger timetable I have seen for that line is 1903, showing three return services, which I assume was standard for most of the time. The branch was completely closed in July 1950, and the following month saw the withdrawal of all Cookstown Junction-Cookstown / Macfin passenger trains and the total closure of the Derry Central north of Kilrea. Five years later, the Cookstown-Magherafelt goods ceased, the Cookstown Junction-Kilrea goods lingering, partly to serve the Upperlands linen mills, until October 1959, the last service of any sort on the Derry Central and Cookstown routes.

The following shows weekday services at Magherafelt in the Summer of 1939:

  • Arrive: 6.00am | Depart: 6.10am | Belfast – Cookstown goods
  • Arrive: 7.05am | Depart: n/a | Light engine from Cookstown
  • Arrive: 7.51am | Depart: n/a | Passenger from Cookstown
  • Arrive: 7.58am | Depart: 8.10am | Belfast – Portrush (via Derry Central Line) passenger
  • Arrive: 8.00am | Depart: 8.04am | Coleraine – Belfast (via Derry Central Line) passenger
  • Arrive: n/a | Depart: 8.11am | Magherafelt – Cookstown passenger
  • Arrive: n/a | Depart: 8.45am | Magherafelt – Draperstown goods
  • Arrive: 10.25am | Depart: n/a | Coleraine – Magherafelt goods
  • Arrive: 10.58am | Depart: 11.35am | Mixed from Cookstown; goods only forward to Belfast
  • Arrive: 11.05am | Depart: n/a | Draperstown – Magherafelt goods
  • Arrive: 11.14am | Depart: 11.18am | Belfast – Portrush (via Derry Central Line) passenger
  • Arrive: n/a | Depart: 11.23am | Magherafelt – Cookstown passenger
  • Arrive: n/a | Depart: 12.30pm | Magherafelt – Coleraine goods
  • Arrive: 1.01pm | Depart: 1.04pm | Cookstown – Belfast passenger
  • Arrive: 3.56pm | Depart: n/a | Cookstown – Magherafelt passenger
  • Arrive: 4.00pm | Depart: 4.07pm | Portrush – Belfast (via Derry Central Line) passenger
  • Arrive: 5.38pm | Depart: 5.41pm | Belfast – Cookstown passenger
  • Arrive: n/a | Depart: 5.45pm | Magherafelt – Portrush (via Derry Central Line) passenger
  • Arrive: 8.26pm | Depart: 8.32pm | Portrush – Cookstown (via Derry Central Line) passenger


The Sunday arrangements were slightly odd: morning trains from Belfast and Cookstown combined at Magherafelt and ran through to Portrush, with a reverse of these manoeuvres in the evening; a morning Magherafelt-Cookstown and evening Cookstown-Magherafelt connecting service allowed day excursions from Belfast to Cookstown. There were pathways for “as required” excursions over the Derry Central, and you can always add livestock specials, overload goods and services for some of those holidays peculiar to the north of Ireland for additional variety. This was one line where the Second World War brought much more traffic: by June 1945, there were five daily Belfast-Cookstown services, and an equal number of Derry Central trains, although only the last up Derry Central ran through to Belfast and all others were connection to or from Magherafelt. There were also several local services between Magherafelt and Cookstown; and extra Saturday trains (including a through Derry-Macfin-Magherafelt service); and two Sunday Belfast-Coleraine workings with Cookstown connections. Most of the BNCR and later NCC locomotive classes could be used, except for the Moguls and Jeeps.

The layout at Magherafelt was quite complex: a signal diagram has not yet come to light, but, especially with the need for somersault brackets, full working signalling would provide quite a challenge. The Draperstown line seems to have been worked by train staff and ticket, with the staff unlocking the points at Desertmartin, which was not a block post. The other lines were operated by electric train tablets, the block sections running from Magherafelt to Castledawson and Moneymore on the mainline and Maghera on the Derry Central. Just to the west of Magherafelt, Cookstown Urban District Council had a quarry with siding connection released by the train tablet. A telephone circuit connected the quarry with Magherafelt signal cabin, and before blasting rock there, the foreman had to call the signal man who removed a tablet for the block section to Moneymore, under the “Release tablet for intermediate siding” rule and sent this with a railway employee to the quarry, where he remained until blasting was complete, and he could return to the station, report all clear and deliver up the tablet to clear the block section.

The main two platforms had access to the Cookstown and Draperstown lines; one and the bay on the north side had access to the Derry Central. Dimensions are taken from the track plan in the IRRS archives and I did check the platform lengths: the figures quoted for the two sides of the island platform defy geometry, but are correct! Similarly, the carriage shed really was only 69’, barely long enough for two six-wheelers. The locomotive facilities were grouped off this section, and there is a photo of these in the Stephenson Locomotive Society Collection (Camwell 25553). The goods facilities on the southside were quite commodious for Irish standards, and include the unusual feature of a cattle bank with a siding on each side and a store with two roads through it. Both the original and my sketch have, I suspect, rather exaggerated the width of the warehouse. One, or at a pinch, two siding in the yard could be omitted and in view of the linear compression most modellers will need to apply, I suspect the crossover between the two main platforms could also be left out. There are a few photos in the Stations UK collection (RR7202, 6123) and the Real Photographs list (X5748, X218, but the modeller would need to do some more research on the main buildings.

Toome Bridge
Always base your model stations on a real prototype, or you may end up with a real howler… like a level crossing in the middle of the passing loop! After Magherafelt, we move two stops up the line towards Belfast to Toome: the inclusion of “Bridge” in the name was a bit variable. By whatever title, the station opened in 1856, and lost its last service, the daily Cookstown-Kilrea goods in October 1959. It was located 36¼ miles from Belfast and 11¼ miles from Cookstown Junction. The notes above on timetables give a fair idea of the train service, although Toome usually had one extra goods train, a morning Antrim or Cookstown Junction-Castledawson working, which in the 1940s ran through to and from Magherafelt. Passing places with only one passenger platform were quite common in Ireland, but usually (and it seems the case at Toome), the crossings were of a goods and passenger or two goods trains. Up and down passenger trains could be handled simultaneously, but there were usually special rules for such occurrences, involving bringing both to a halt at the home signal and flagging one into the loop, or shunting one if both were scheduled to serve the station. In the 1930s, the electric tablet block sections were Cookstown Junction-Toome and Toome-Castledawson, the sidings at Randalstown and Staffordstown being released by the Cookstown Junction-Toome tablet.

I don’t seem to have date for this track plan, so I am guessing that the NCC might have extended the loop in the Second World War and that the need to increase line capacity took priority over moving the road. Toome was the rail head for a military aerodrome during this period. The Northern Brick & Sand company had a 2’ line serving sand pits to the south of the NCC line, and Toome also handled a heavy sand traffic for wartime construction work. There were also extra troop trains: in October 1943 when many soldiers passed through Belfast, to relieve the GNR route, some troop trains to Armagh ran via the NCC Cookstown line. Another adaptation to such extra traffic was that Randalstown signal cabin, closed by the NCC as an economy, was reopened to divide the Cookstown Junction-Toome block section. Even the Draperstown branch was “called up” with a US army depot near Desertmartin and extra traffic to the terminus for mock battle exercises.

Toome Bridge

Toome Bridge

The division of goods facilities, store on one side of the running line, loading bank and carriage dock on the other is unusual. If my reading of Stephen Johnson’s atlas is correct, the three siding serve Toome Quays. So, there may have been some wharves for interchange with water-borne traffic there: the Bann joins Lough Neagh just to the south. Loose shunting on these sidings was forbidden in the appendix to the working timetable. Rather confusingly, the plan is drawn with west to the right hand side! The bridge over the river (officially one of the various Carlisle Bridges in Ireland), was a lattice girder, with a central swivel span turning on a masonry pier. This opening span was locked by a Pinkerton’s Patent Point Box and needed the Toome-Castledawson tablet to release it.

If you could track down some photographs, the river, bridge and wharf should provide the opportunity for some scenic modelling. I imagine that one of the sidings to the quay could be omitted without much loss of operational scope. No signal box diagram has come to light, but the track plan clearly showed independent traps for the pair of sidings and the one to the loading bank. There are two pictures in the Stations UK collection (RR6712, 1509).

Johnson S (1997) Johnson’s Atlas & Gazetteer of the Railways of Ireland Leicester: Midland Publishing.
London Midland & Scottish Railway NCC (1946) The Operating Department in War Time 1939-1945 Belfast: W&G Baird


Leave a comment

Filed under Site Surveys

“Nearly Irish”

Colm Flanagan


With the arrival of our first really good RTR Irish diesel, and coaches to match by the time this is published, the thoughts of some modellers are beginning to consider whether a steam loco might be viable as a commercially produced model.  If this were so I’d vote for the LMS NCC/UTA/NIR/RPSI Class WT (Jeep) 2-6-4T.  Will it happen; who knows? But in the meantime, are there any ways of getting something like it?  The similarity between the ex-NCC 2-6-4T and its British mainland counterparts has often been remarked upon and in the last few years we have been favoured with Hornby and Bachmann giving us just about all the variants of the LMS/BR “equivalents.”  Over the past few years, as readers of New Irish Lines may remember, I have been building a chopped version of the Hornby Fowler tank which most folk have been very kind about.  New models of the UK 2-6-4Ts have appeared since then, so I thought it might be of interest to do a “state of play” round up, specifically looking at which, if any, of these is closest to the “Jeep.”  There were five variants (that I know of) on the theme:

  1. The original Fowler tanks produced for the LMS.  Modelled by Hornby in the 1980s and ’90s.  A super-detailed version was produced more recently; a renumbered version of this is due this autumn.
  2. Some later versions received side window cabs.
  3. Stanier then produced a variant with a taper boiler, whose dimensions were otherwise the same as the Fowler.  Hornby have recently produced this one.
  4. Fairburn produced a similar locomotive with a slightly shorter wheelbase.  Modelled by Bachmann – still available.
  5. BR produced a standard 4MT tank rather similar to the Fairburn; Hornby Dublo first made a model of this in the 1950s and Bachmann do a model which has been in their catalogue since 2002.

It was between the appearance of 4 and 5 that Ivatt supervised the building of the “Jeeps” – they were possibly designed by Stanier back in 1943 (according to JRL Currie) but building didn’t actually start until 1945.  The first 10 arrived in Northern Ireland in 1946-47, the latter eight 1949-50 (50 was the last actually delivered to the NCC, the rest to the UTA).  So, we seem to have quite a bit of choice.

To begin the consideration, we have to bear in mind certain things.  All of the English locos had wheels 5′ 8″ or 5′ 9″ whereas the Jeeps had 6′ 0″.  The Jeeps had a smaller diameter bogie and pony truck wheel; all of the English locos had longer fireboxes/boilers and shorter bunkers than the Jeeps.  With the exception of the Fowler (1 and 2) they had different wheelbases, mostly between the front pony truck and leading drivers.  Therefore for total accuracy, build your own, or wait in hope for a scale RTR model.  Anyone following either of these approaches may read no further!

Next a major issue: by the time the Jeeps were built, taper boilers were the norm in England, but the Jeeps had a parallel boiler, as it was decided to use the same one as had been used for the earlier mogul tender engines.  On the face of it this rules out all variants except 1 and 2.  However, let us assume that you don’t want to carry out major surgery (and it would be major: I certainly haven’t even tried it!)  Taking the most modern engine first:

The BR Standard 4MT:
Built some years after the Jeeps.  This has side window cabs and a built up bunker which looks reasonably “Jeep-like.”  Also, the front cylinders are high and angled, again, quite good.  This is the only one to have the correct pattern of two steps to the tank undersides, although an early drawing shows the single step on No. 5, the first to be delivered.  This is of course an error as any photographs will quickly show.  There is a continuous footplate, though the Jeep had a cutaway.  However, the “look” of it (whichever version, Dublo or Bachmann, you use) is just too “heavy” in my eyes and that, coupled with the points above, rules it out.

The Fairburn:
The first of which were built in1945, shortly before Ivatt took over as LMS loco superintendent.  Fairburn died suddenly in October 1945 and was replaced by H G Ivatt.  As the BR version has side window cab and bunker, these look more angular than the BR one.  This loco also has a cutaway front footplate.  It has a single step under the side tanks.  Allowing for the points made above, it looks not unlike a Jeep to my eyes.  One slight issue is that there is a definate “kink” in the top of the side bunkers, though this isn’t really noticeable on the model.

The Stanier:
Built in the 1930s.  Side window cab bunker, similar to Fairburn, but with a continuous footplate, similar Fowler frames and the cylinders are at a lesser angle to the horizontal.

The Fowler rebuild:
Built in the late 1920. The good news!  Wheel base dimension is accurate.  Side window cab (though see above); no cutaway on the footplate, and cylinders as Stanier design.  But it has a parallel boiler which is correct, and it’s a bit long overall (as is the original).  If you contemplated doing a small bit of chopping this would get you near with cutting away the footplateand altering the profile of the tank underside, neither a big job.  The bad news: this is the one variant nobody currently makes!

The Fowler original (1926-27):
As above but the cab has no side windows, these have to be cut out and new window frames made, which is what I did on my own conversion; I also cut away the cab and this lengthens the bunker, then did other things, etc. to produce my engines, which take it out of this survey’s remit.

So my conclusion?  If I wanted something “Jeep-like” with no work, just a repaint job essentially, I’d get a Fairburn.  For a little extra work, alter the bunker underside, fit a handwheel to the smokebox (a very Irish thing, that) and repaint, even better.  If you are prepared to do more, than I reckon the Fowler is the better bet to start from.  You’re still left with some compromises of course, but so far that’s the best I’ve come up with.  And if Murphy Models or someone else decides to go for the first proper scale Irish RTR steam loco, my vote goes for a Jeep.  In UTA days they were found on every line still open, they took excursions to Dublin, and in RPSI ownership No. 4 has travelled everywhere in Ireland and still operates today.  The “universal” engine, in a way its builders would never have foreseen.  It could look equally at home with a rake of Cravens coaches of any era, NCC/UTA coaches of Midland style, or the RPSI set.  Of course, if this superbly detailed ultra-accurate WT appeared then I might have some secondhand conversions for sale on eBay!


Filed under Modelling